电磁加热器的安装和使用注意事项！

Attention to the installation and use of electromagnetic heaters!

在使用电磁加热器之前，消费者应该按照安装和操作说明仔细阅读产品手册。一般的电磁加热器应放置在坚固的平台上或悬挂在设备上，附近的温度不宜过高，防止过热保护造成散热不良。电磁加热器前面的外部电源。

Before using the electromagnetic heater, the consumer should read the product manual carefully according to the installation and operation instructions. The general electromagnetic heater should be placed on a solid platform or hung on the equipment, and the temperature nearby should not be too high. The external power supply in front of the electromagnetic heater.

电磁加热器的注意事项

Attentions of electromagnetic heaters

1，非专业人员不拆卸，维护本产品。

1, non professional personnel do not disassemble and maintain this product.

2，产品出现故障不排除不能修复时，请联系厂家解决。

2, product failure does not rule out repair, please contact the manufacturer to solve.

3，如果加热线圈损坏，必须由我们的维修部门或专业人员进行更换。

3, if the heating coil is damaged, it must be replaced by our maintenance department or professional personnel.

4，请使用与交流电源相同的铭牌电压值。

4, please use the same nameplate voltage value as the AC power supply.

5，请使用合格的电源地保护，以确保人身安全。

5, please use qualified power supply to ensure personal safety.

6，请勿放在易燃易爆物品上或使用时，请勿放在潮湿或靠近其他热源的地方，以免造成故障和危险。

6, do not place on flammable and explosive materials or when used, please do not place it in damp or near other heat sources, so as to avoid causing trouble and danger.

7，接入电源线时，必须连接好，保证接触良好。

7, when the power line is connected, it must be connected to ensure good contact.

8，产品在工作中不动。

8, the product is not moving in the work.

9，由于电磁加热器是通过电磁感应加热装置的，所以使用金属工作台时不能放在旁边的线圈支架上，否则，输出功率正常，严重时可能导致电磁加热器重负荷而损坏。

9, because the electromagnetic heater is through the electromagnetic induction heating device, so the use of metal worktable can not be placed on the side of the side of the coil bracket, otherwise, the output power is normal, serious time may cause heavy load and damage to the electromagnetic heater.

10，电磁加热器的使用应具有良好的铸铁，铸钢的磁性能。

10, the use of electromagnetic heater should have good magnetic properties of cast iron and cast steel.

11，电磁加热器在使用中关机，由于延时风扇设定程序关机过程中。所以应该是内部冷却风扇在关闭电源之前自动停止转动，使电磁加热器的内部元件完全冷却，确保相关元件不会过热和损坏。另外，电磁加热器在停机状态下，只有驱动电路输出电压，其他电路仍然处于电源待机状态。所以，电磁加热器不在使用中，所以总电源关闭。否则，不仅浪费电力成本，而且还会长时间影响电子元件的使用寿命，因线圈长期积累的热量损坏。

11, the electromagnetic heater is switched off during use, due to the delay fan setting procedure during shutdown. Therefore, the internal cooling fan should be automatically stopped before turning off the power supply, so that the internal components of the electromagnetic heater are completely cooled to ensure that the related components are not overheated and damaged. In addition, when the electromagnetic heater is in shutdown state, only the output voltage of the driving circuit is still, and other circuits are still in standby state of the power supply. Therefore, the electromagnetic heater is not in use, so the total power supply is off. Otherwise, not only will the electricity cost be wasted, but it will also affect the service life of the electronic components for a long time.

12，电磁加热器工作时不能接触线圈，防止烫伤。

12, the electromagnetic heater can not contact the coil when working, so as to prevent scalding.